Current position: Product list Product details
< >

0.66 Inch 64×48 OLED Display Mini Screen

SCE066001-V03 is a OLED Display with COG Type, 64×48 Resolution, SSD1306BZ IC, 6800/8080 interface 4 wire serial interface I2C, 30PIN

  • Type: OLED
  • Mode: -
  • Product No: SCE066003-V01
  • Size: 0.66''
  • Resolution: 64*48
  • Outline Dimension: 18.46*18.1*1.21
  • Active Area: 13.42*10.06
  • Interface: 6800/8080 Interface/I2C/ 4-wire SPI
  • IC: SSD1306BZ
  • Brightness: -
  • Touch Screen: No
  • View Direction: -
  • Pin No: 30
  • Shape: Rectangle
Inquiry Now

Introduction:

General Specification

 

ITEMSPECIFICATIONSUNIT
 MODULE SIZE18.46(W)x18.1(H)x1.21(D)mm
 VIEWING AREA15.42 (W) x 12.06(H)mm
 ACTIVE AREA13.42 (W) x10.06(H)mm
 DOT SIZE0.19(W) x0.19(H)mm
 DOT PITCH0.21(W) x0.21 (H)mm
 ASSY.TYPECOG
 WEIGHTTBD

Interface Definition

 

PIN NO.SYMBOLTYPEFUNCTION DESCRIPTIONS
1NC
NC.
2C2P
C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3C2N
4C1PI
5C1N
6VBATPPower supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7NC
NC.
8VSSPGround pin. It must be connected to external ground.
9VDDPPower pin for logic circuit. It must be connected to external source.
10NC
NC.
11BS1IBitmap Interface selection pins.
12BS2
13CS#IChip Select input pin. Active “L”
14RES#IHardware reset input pin. Active “L”.
15D/C#IThis is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16R/W#IThis is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17E/RD#IThis is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18D0I/OThese are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19D1
20D2
21D3
22D4
23D5
24D6
25D7
26IREFICurrent reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27VCOMHOCOM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28VCCPPower supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29NC
NC.
30NC
NC.


Technical support

Previous Product Previous Product : 0.66'' 64×48 SSD1306BZ OLED Display

Next Product : 0.69 inch Miniature 96×16 OLED Display Next page